1. Before using the lift, please read the instruction manual carefully to understand and master the use procedure of the machine.
2. The operator should be familiar with and master the safe operation procedures of Article 4.
3. Unfold (insert) the legs:
In order to ensure personal safety and prevent accidents, the machine is equipped with four legs. Before use, the legs should be fully opened (use the legs to be inserted into the sleeve on the chassis at least 200mm when inserting the legs). Rotate the four legs of the top screw handles, which are close to the feet.
Second, the adjustment level:
Adjust the four screws so that the support feet are firmly on the ground and the equipment base must be level
Third, the inspection before starting
Before using the lift, please conduct a comprehensive inspection of the whole machine to lubricate the relevant parts.
(1) Check the chain system: Before starting the machine, carefully check the running condition of the chain system, adjust if necessary, make the chain evenly tightened, lock it with the backup mother, and lubricate the parts of the chain, and add a little to the sprocket 20 No. Engine oil; people stand on the ground and press the up and down buttons. Check the mechanical operation status, see if the chain is disengaged from the sprocket, and see if the sprocket support plate is loose;
(2) Check the fuel tank: Before starting the machine, check if there is enough hydraulic oil in the fuel tank. If it is not enough, it should be replenished in time.
(3) Check the power supply voltage level and check whether the action of each circuit breaker is sensitive:
(4) For double-column products, check whether the lifting of the two side rails is synchronized. If there is any unsynchronization, please contact the professional technicians before use.
(5) All the above inspections have been debugged and qualified, and no adjustment is required before use. Can be used for future maintenance reference.
Fourth, the way the operator works on the platform:
The operator should lift the railing from the front or enter the guardrail through the ladder and lock the guardrail in the correct position. The operator stands in the center position and presses the ascending button to make the working platform rise slowly and stop at the desired position to start working. Do not shake or cross the guardrail when working at heights to avoid accidents. Press the down button to drop. If there is a sudden power outage during work, the emergency manual control descent device can be activated to safely land the elevator and return to the initial position.
Pallet type continuous lift type
The pallet type continuous lift has the distinction of "Z" type "C" type and "H" type. The goods of the “Z†type elevator form a “Z†type trajectory in the inlet direction and the outlet direction; the “C†type trajectory is formed in the cargo inlet direction and the outlet direction of the “C†type elevator. The “H†type trajectory is formed in the direction of the cargo inlet and outlet of the “H†type elevator. The “H†type lift is imported on one side and the material outlet on the other.
Tray type continuous lift advantages
The continuous lift is safe and reliable, easy to maintain, and low in operating costs, effectively reducing transportation costs. Applicable to the finished products of home appliances, food, medicine, tobacco, coating chemicals, etc.. Vertical transportation of logistics. [1] The material of the frame is angle steel, which is covered with a special aluminum material and sealed by a sun plate. The motor uses SEW with brake motor. Tray type continuous lift technical parameters The length of the continuous lift is about 730mm of the tray length, the width is about 670mm of the tray width, the lifting height is h, and the total height is H. The length of the tray is about the length of the object +300mm, the width is about the width of the object +100mm; the total height H is equal to the lifting height h+h1+h2 (h1 is the height of the first floor working face, h2 is the height above the working surface of the second floor, the size According to the height of the object to be determined.) The relevant parameters of the "H" type continuous lift are determined separately according to the size and shape of the material. The recommended load is up to 500kg/piece; the lifting speed is up to 35m/min; the length of the object is 1.2m; the width of the object is 1.2m; the height of the object is 1.2m; the height of the first floor is 650mm; the system is at least 4s. The above parameters can be customized according to your needs.