Automatic electromagnetic induction aluminum foil sealing machine use precautions:
1. It is not suitable for metal containers and metal covers. It is not allowed to press the start button on the metal table, otherwise it will damage the machine.
2. Insert the induction air plug and tighten the screw before turning on the power.
3. Use single-phase three-wire power cord. For operator safety, be sure to use single-phase three-wire power socket. The work floor must be dry to keep insulation.
4, with temperature overheating automatic protection, when the internal temperature of the machine is overheated, the buzzer sounds " abnormal protection (PRO.MD.)" yellow light is on, the power supply main switch should be turned off, standby cooling After the buzzer stops, continue working.
5. During the working process, always touch the surface of the sensor head to check whether it is overheated. If it is found that the hot hand should stop heating, wait until it is cooled before working (cooling can not turn off the power), when the “WARMUP†green indicator light is off, please Do not press the start button to avoid false triggering. When the unit is finished, turn off the power switch on the panel.
6, equipped with a fuse of 5A, not available for greater than 5A insurance instead.
7. There is high voltage inside, the bottom plate is charged, and it is strictly forbidden to repair it personally to avoid personal electric shock.
8. If it is found that there is a bare wire before use, stop using the machine and use it after repair.
9. The equipment should not be impacted, stressed or damp when transported, stored or used.
10. When the product is inspected and checked out, in the case of normal transportation and good packaging, if the parts of the product are found to be inconsistent with the packing list, they should be promptly sent to the company.
11. According to the instruction manual, the operation should be clearly understood in advance. If the quality of the product is found, it should be explained to the company within the prescribed time limit.
Cleaning and maintenance of automatic electromagnetic induction aluminum foil sealing machine:
Regularly clean the surface of the machine, the bottom plate and the lower die slide, the groove, the upper mold inner pressure plate and the positioning rod (Note: the power must be turned off and the normal temperature is restored).
The lower die slide, the pressure bar bearing, the eccentric wheel and the guide post, the guide rail and other transmission parts are regularly added with butter to ensure the performance of the machine.
To clean the cutter: first use the cotton ball to plug the two drain holes of the lower mold, pour the boiling water into the groove of the lower mold, fill it up, then push the lower mold slide into place, press the upper mold down, press To the low point of zui, let the tooth knife soak for a few minutes until it is clean, and repeat it several times.
1. It is not suitable for metal containers and metal covers. It is not allowed to press the start button on the metal table, otherwise it will damage the machine.
2. Insert the induction air plug and tighten the screw before turning on the power.
3. Use single-phase three-wire power cord. For operator safety, be sure to use single-phase three-wire power socket. The work floor must be dry to keep insulation.
4, with temperature overheating automatic protection, when the internal temperature of the machine is overheated, the buzzer sounds " abnormal protection (PRO.MD.)" yellow light is on, the power supply main switch should be turned off, standby cooling After the buzzer stops, continue working.
5. During the working process, always touch the surface of the sensor head to check whether it is overheated. If it is found that the hot hand should stop heating, wait until it is cooled before working (cooling can not turn off the power), when the “WARMUP†green indicator light is off, please Do not press the start button to avoid false triggering. When the unit is finished, turn off the power switch on the panel.
6, equipped with a fuse of 5A, not available for greater than 5A insurance instead.
7. There is high voltage inside, the bottom plate is charged, and it is strictly forbidden to repair it personally to avoid personal electric shock.
8. If it is found that there is a bare wire before use, stop using the machine and use it after repair.
9. The equipment should not be impacted, stressed or damp when transported, stored or used.
10. When the product is inspected and checked out, in the case of normal transportation and good packaging, if the parts of the product are found to be inconsistent with the packing list, they should be promptly sent to the company.
11. According to the instruction manual, the operation should be clearly understood in advance. If the quality of the product is found, it should be explained to the company within the prescribed time limit.
Cleaning and maintenance of automatic electromagnetic induction aluminum foil sealing machine:
Regularly clean the surface of the machine, the bottom plate and the lower die slide, the groove, the upper mold inner pressure plate and the positioning rod (Note: the power must be turned off and the normal temperature is restored).
The lower die slide, the pressure bar bearing, the eccentric wheel and the guide post, the guide rail and other transmission parts are regularly added with butter to ensure the performance of the machine.
To clean the cutter: first use the cotton ball to plug the two drain holes of the lower mold, pour the boiling water into the groove of the lower mold, fill it up, then push the lower mold slide into place, press the upper mold down, press To the low point of zui, let the tooth knife soak for a few minutes until it is clean, and repeat it several times.
Digital Imaging Equipment,X-Ray Equipment And Accessories,16 Slice Ct Scan,Ct Scanner
Shanghai Rocatti Biotechnology Co.,Ltd , https://www.shljdmedical.com