Instructions for use of wooden shredders and precautions 1. Before starting, it should be strictly checked whether the installation of various parts of the machine meets the requirements. Metal objects should not fall into the machine. First, try to run the belt with hands to see if there is any bite and turning. Shells and other phenomena to avoid accidents.
2, the boot sequence: first open the fan, then open the host, stop the machine after stopping the machine and stop the fan.
3, should be kept even when adding materials, the feeding particle size according to the hardness of the material, the diameter of the hard material should not exceed three centimeters, metal lumps are strictly prohibited from entering the lower opening.
4. During the use, the motor load should not be overloaded and keep running normally.
5, should always check the wear process of the blade and the grinding plate. If it is found that the blade grinding plate is seriously worn, it should be replaced in time.
6, the method of adjusting the fineness:
(1) According to the fineness requirement, the adjustable blade can be adjusted to the left and right in the axial direction. The smaller the clearance of the oblique blade from the tapered surface, the smaller the fineness and the larger.
(2) Test the hood: The bonnet lowers the fineness of the bottom and vice versa.
(3) Adjusting the air volume: the damper is opened and the wind flow is reduced in particle size, and vice versa. If the air volume is too small, the feed nozzle is easy to spray outward.
(4) Adjusting the main fan blades: 2-3 pieces of wind blades in the casing can be reduced if necessary to improve the fineness. This method can also be used when spraying the powder in the return nozzle. The above four methods can be adjusted from 20 to 325. Head.
7. When the hammer of the wood powder machine is worn, the angle can be changed four times. After using the zui, it can be reused by welding with high-chromium wear-resistant welding rod.
The speed of the wood powder machine is higher than that of the installation foot. It must also have a good lubrication of the bearing parts of the main engine. Keep it clean. Add a high-speed butter once a month. If the molybdenum disulfide is better, the bearing temperature is not high under normal circumstances. 70 degrees is normal.
2, the boot sequence: first open the fan, then open the host, stop the machine after stopping the machine and stop the fan.
3, should be kept even when adding materials, the feeding particle size according to the hardness of the material, the diameter of the hard material should not exceed three centimeters, metal lumps are strictly prohibited from entering the lower opening.
4. During the use, the motor load should not be overloaded and keep running normally.
5, should always check the wear process of the blade and the grinding plate. If it is found that the blade grinding plate is seriously worn, it should be replaced in time.
6, the method of adjusting the fineness:
(1) According to the fineness requirement, the adjustable blade can be adjusted to the left and right in the axial direction. The smaller the clearance of the oblique blade from the tapered surface, the smaller the fineness and the larger.
(2) Test the hood: The bonnet lowers the fineness of the bottom and vice versa.
(3) Adjusting the air volume: the damper is opened and the wind flow is reduced in particle size, and vice versa. If the air volume is too small, the feed nozzle is easy to spray outward.
(4) Adjusting the main fan blades: 2-3 pieces of wind blades in the casing can be reduced if necessary to improve the fineness. This method can also be used when spraying the powder in the return nozzle. The above four methods can be adjusted from 20 to 325. Head.
7. When the hammer of the wood powder machine is worn, the angle can be changed four times. After using the zui, it can be reused by welding with high-chromium wear-resistant welding rod.
The speed of the wood powder machine is higher than that of the installation foot. It must also have a good lubrication of the bearing parts of the main engine. Keep it clean. Add a high-speed butter once a month. If the molybdenum disulfide is better, the bearing temperature is not high under normal circumstances. 70 degrees is normal.
Our company`s Dry-milling machine. It was added to the Demetdent family of dental milling devices in answer to our lab and dental users need for a dry-milling option to handle many of the new brands and materials. The dry Dental Milling Machine fills a gap in many dental restoration workflows, giving laboratories the added flexibility of milling zirconia, wax and PMMA materials that are becoming increasingly popular in the industry.
Cerec Milling Machine,Roland Dental Mill For Sale,Mini Paddy Dryer Machine,Roland Milling Machine Dental
Shandong Carved Intelligent Technology Group Co.,Ltd , https://www.demetdent.com