Because corn has the characteristics of high water content, slow dehydration, and vulnerability to frost, once it is not good, “water corn†and “mold grain†will appear. Commercial corn will not be graded and will not sell well; corn seed contains Large amounts of water, intolerant to safe storage, easy to destroy species, therefore, we must do everything possible to reduce the moisture content of corn, in particular, corn seeds should be reduced to safe water (14%) to ensure safe storage.
Field precipitation
1, stand stalks, skin dry. There are many advantages for drying corn stalks and stalks. One is to reduce the moisture content of corn by 5-9%, the second is to ripen 5-7 days earlier, the third is to increase corn production by 5-7%, and the fourth is the maturity of corn seed. The drying time of corn bran skin is very important. It can neither be too early nor too late. It prematurely affects the transformation of the nutrients in the ear, leading to a decline in corn production. It also loses the significance of drying the skins of the China Mobile Peasants ICT website too late. Should be mastered at the end of corn wax, that is, when the seeds form a layer of hard cover, the best time is not to slurry by hand. The method is to open all the leaves, so that all the ears exposed.
2, field sorghum drying. While harvesting the ear, the corn culm is cut off, leaving about 50 kilograms of maggots, and then the panicles of the panicles are cut off, leaving 3-4 pieces of leaves inside, bundled every 6-8 pieces of fruit, and hung together. On stilts, with gongs, princes, and gongs, rotate once every 2-3 days.
3, straw stalk rod. Generally during the harvest period, put the corn sticks in the light and put a layer of corn stalk under it. This will prevent moisture and precipitation. It is best to turn 2-3 times during this period to accelerate dehydration.
Yard Precipitation
1, hanging dry. In the farmer's home, use wooden sticks, wire, ropes and other objects to build a shelf, raise about 150 kilograms, and then 8-9 ears will be detected together, on the shelf, 2-3 turn once, accelerate the rate of precipitation .
2, drying in the drying field. Will remove the wrapped leaves, filaments of clean corn ear, flat on the drying floor, for drying, require the ear to spread evenly, not too thick, turn 2-3 times a day.
3, bagging drying. The ear of corn that is used for seeding can be bagged and air-dried. The method is to remove the clean leaves and the ear of filaments, place it neatly in a mesh bag, and then place it evenly on a well-ventilated wall, wooden frame, or roof. , Every 2-3 days flip once, bagged ears should not be too much, too real, so as not to affect the ventilation and light, reduce the dehydration effect.
4, stack drying. Sew stalks on the ground, put together 2 to 6 corn spikes (the corn leaves do not leave the net, leaves a few leaves inside), and then hang on the stack, corn sticks from the ground to maintain a distance of 30-50 cm.
5, building drying. Use wood or sunflower stalks, corn stalks, or sorghum stalks to build a corn house and put corn ear in the building to speed up dehydration.
6, rod rope drying. Coarse corn sticks, put them on rods or ropes, and dry them by dehydration.
Precipitation
1, in the yard or yard, sweep clean, and then spread the corn kernels, spread into a thin layer, often turning, speed up the ventilation and light, and promote rapid dehydration.
2, using a dryer, mechanical drying dehydration.
3, fire and precipitation, in case of special years, the seed moisture continues to be high, should take fire pod species, but the temperature should be appropriate, often flip, heat evenly.
Multi- Parameter Patient Monitor
A multiparameter monitor is a medical device for monitoring a patient`s vital signs. It is mainly used in intensive care, hospitalization or ER. In general, basic models are used to monitor cardiac activity (ECG), blood pressure (NIBP), respiration (RESP), oxygen saturation (SpO2) and temperature (TEMP).
They display the value of each parameter while presenting the evolution curves over time. For some models, modules can be added to measure other parameters (ETCO2, CO2, pCO2, IBP, EEG, EMG, etc.). They have audible and visual alarms to alert medical personnel to any risks related to the patient`s condition.
Multi- Parameter Patient Monitor,multiparameter monitor,parameter patient monitor,parameter monitor
Ningbo Queen Electronic Science Technology Co., Ltd , https://www.queenmeds.com